7Semi MCP73833 Li-Ion / LiPo Battery Charger Board – USB-C

(No reviews yet) Write a Review
$4.50
SKU:
BO-10242
Adding to cart… The item has been added

The 7Semi MCP73833 Li-Ion / LiPo Battery Charger Board is a compact, standalone charging solution designed for single-cell rechargeable lithium-ion and lithium-polymer batteries. Built around the Microchip MCP73833 charge management controller, the module provides reliable battery charging through a USB-C 5V power input without requiring an external microcontroller, firmware, or additional charging circuitry.

The board uses a controlled constant-current/constant-voltage (CC/CV) charging algorithm, incorporating battery preconditioning, automatic charge termination, and automatic recharge. The MCP73833 supports resistor-programmable charging currents up to 1A, while the FCI variant provides a regulated 4.20V charging voltage for compatible single-cell Li-Ion and LiPo batteries. The actual charging current depends on the installed programming resistor, available input power, and thermal conditions.

For flexible charging configuration, the board features factory-installed SMD resistors for PROG and THERM, along with dedicated through-hole connection pads for customization. Users can remove the corresponding default SMD resistor and install a suitable through-hole resistor in the PROG position to adjust the charging current. Similarly, the THERM configuration can be modified using an appropriate resistor or compatible NTC thermistor circuit for battery temperature monitoring. This design allows users to customize the charging behavior according to their battery requirements without redesigning the PCB.

The charger incorporates multiple safety-related functions, including thermal regulation, input undervoltage lockout, and reverse-discharge protection. Thermal regulation automatically reduces the charging current when the IC temperature rises, helping maintain controlled operation under varying input and environmental conditions.

For convenient operation, the module includes three onboard LED indicators labeled CHARG, DONE, and PWR, providing visual indication of charging activity, charge completion, and input power availability. 

With its compact 34 x 12 mm PCB, USB-C connectivity, configurable charging current, and standalone operation, the 7Semi MCP73833 Battery Charger Board is suitable for portable electronics, rechargeable sensor nodes, IoT devices, battery-powered prototypes, robotics, and embedded development applications.

Key Features

  • Single-Cell Li-Ion / LiPo Charging: Designed for charging compatible single-cell rechargeable lithium-ion and lithium-polymer batteries.

  • USB-C Power Input: Features a USB-C connector for convenient charging from a regulated 5V DC power source.

  • MCP73833 Charge Controller: Built around the Microchip MCP73833 for reliable, standalone battery charge management.

  • Constant-Current/Constant-Voltage Charging: Uses a CC/CV charging algorithm for controlled and efficient battery charging.

  • Programmable Charging Current: Supports resistor-programmed charging currents up to 1A at the IC level, depending on the installed resistor and operating conditions.

  • Customizable PROG Resistor: Includes a factory-installed SMD programming resistor that can be removed and replaced with a suitable through-hole resistor using the dedicated PROG pads.

  • Configurable THERM Input: Features a factory-installed SMD resistor that can be replaced with a suitable resistor or compatible NTC thermistor circuit through the dedicated THERM pads for battery temperature monitoring.

  • 4.20V Charge Regulation: Provides a regulated 4.20V charging voltage for compatible single-cell Li-Ion and LiPo batteries using the MCP73833 FCI variant.

  • Battery Preconditioning: Supports controlled preconditioning of deeply discharged compatible batteries before normal charging.

  • Automatic Charge Termination: Automatically terminates charging when the battery reaches the programmed charge-completion conditions.

  • Automatic Recharge: Automatically restarts charging when the battery voltage falls below the recharge threshold.

  • Thermal Regulation and Shutdown: Automatically reduces charging current when the IC die temperature rises above approximately 95 deg C to prevent overheating. Charging is suspended if the die temperature exceeds 150 deg C and resumes after cooling by approximately 10 deg C.

  • Integrated Protection Features: Includes input undervoltage lockout and reverse-discharge protection for controlled charging operation.

  • Three LED Status Indicators: Features CHARG, DONE, and PWR LEDs for visual indication of charging activity, charge completion, and input power.

  • Standalone Operation: Operates without an external microcontroller, firmware, or software configuration.

  • Compact PCB Design: Features a 34 x 12 mm board suitable for space-constrained applications.

  • Versatile Applications: Suitable for portable electronics, rechargeable sensor nodes, IoT devices, robotics, embedded systems, and battery-powered prototypes.

 

_resources_datasheet:
https://drive.google.com/file/d/1QEb5RGUUo4doGrrD0ePjUYF62cbeFJSr/view?usp=sharing
Charger IC:
Microchip MCP73833
Battery Compatibility:
3.7V Single-cell Li-Ion / LiPo
Charge Regulation Voltage:
4.20V
Input Connector:
5V USB Type-C
Charging Method:
Constant-Current / Constant-Voltage (CC/CV)
Maximum Charging Current:
Up to 1A
Charging Current Configuration:
replaceable through PROG through-hole pads (Default 1A)
Temperature Monitoring Configuration:
configurable through THERM through-hole pads
Protection:
Thermal regulation, thermal shutdown, undervoltage lockout, reverse-discharge protection, battery temperature monitoring
Status Indicators:
CHARG, DONE, PWR
Battery Connector:
2-pin connector
approximate Dimensions (L x W x H):
34 x 12 x 7.12 mm
_summary:
7Semi MCP73833 USB-C Single-Cell Li-Ion / LiPo Battery Charger Board with Up to 1A Programmable Charging, Configurable PROG and THERM Resistors, Automatic Charge Management, and LED Status Indicators.